Showing posts with label Interior. Show all posts
Showing posts with label Interior. Show all posts

Saturday, November 28, 2009

A Hot Detour

So, after reinstalling the carpet, it was time to get back to the original source of trouble - the heater core assembly.

You may recall that I removed the heater core because it was leaking coolant fluid into the pedal area. This is bad - it can lead to my feet getting scalded, but worse, the pedals would get wet and slippery. Not something you want while pressing the brakes to stop and avoid hitting the guy in front...

To repair the leak, I removed the complete heater assembly, and tore it apart. The heater core itself is a small radiator-like heat exchanger, which heats up air with engine coolant. It looked in good shape, but I had it rebuilt and serviced, just in case. I also removed and replaced the valve that controls flow of coolant to the heater core, which is another potential source of leaks.

From Q's House of Speed


As for the rest of the assembly, it is mostly built of plastic, with a pair of metal doors that open and close in order to guide hot air through the heater core, and out to either the car floor (heater mode) or to the front windshield (defrost mode.) A pair of levers control these flaps. Both flaps were rusty, so I cleaned them up and derusted them using Evapo-Rust rust remover. I then applied some primer and a couple of coats of black Rust Oleum spray paint. This should help keep any new rust from developing.

From Q's House of Speed


The top of the box has a rubber gasket that seals and isolates the whole unit. In my case, there was no gasket, so I had to make one of closed-sell foam rubber material. Simple enough.

So, after all this prep work, the box was reassembled, and made ready for installation. The only problem was this: reinstalling the box requires access to bolts that are impossible to reach once the box is in place - unless you remove the dashboard. I also think that, with all the new insulation in place, the carpet is a bit raised, and does not provide enough room for the box to be installed into place - unless you remove the dashboard.

Sigh....

You know where this is going, right?

Carpet and Insulation

So, with the third brake light installed, I was ready for installing the carpet.

Recall that I removed the carpet in order to replace the interior insulation, which was very grungy and smelly. After installing all of the new insulation, it was time to replace the carpet.

From Q's House of Speed



This is pretty straightforward - just spread the carpet inside the car again. The tricky part is getting the side door sills to install correctly. To do this, one needs to reinstall the rubber trim around the doors. For some reason, the rubber trim seems to have shrunk a bit, and it would not fit all around the door sill. Further, it seems to be too thick, and it is very hard to slip into the groove onto which it fits. After a bit of struggle, I was able to get it close, but it still gets in the way of closing the door.

Sigh...

The door sill themselves were easy to install, though.

The carpet does not smell bad anymore. Which is a good thing. Next up - reinstall the heater box, seats, belts, and the car would be ready to go. Little did I know...

Friday, June 19, 2009

A Light Detour, part 2

Before installing all the interior carpeting I wanted to install a third brake light. I figure this will make things a bit safer by providing better warning to folks when braking. However, while doing all this, I realized I really wanted to get rid of the rear speakers (which were cheapo/ugly units) and all the assorted wiring. After all, I did not have a radio installed anymore, and they were useless.

So, while removing the rear speakers I noticed things might be a bit simpler if I removed the complete rear deck. Removing it was simple - there are three sheet metal screws that hold the piece in place. Undo these, pull the thing out, and it's all done.

The vinyl cover on the tray itself was in OK shape, but it had been cut to make way for the speakers. In all honesty, I think I won't be installing speakers any time soon, which means the holes in the original vinyl just won't work well for me. Which means I have to replace the vinyl fabric.

Sigh...

Vinyl fabric is not uncommon, but for a newbie, it seems hard to find - especially for specialied applications such as automotive stuff. At first sight, I though this would take me a few days (maybe a couple of week) just to find the proper materials to do this.

This is where google comes to the rescue: after a few hours, I had found PerfectFit Wholesalers in in Tukwila, WA (down the street from work.) These folks advertised a variety of vinyl fabrics and the such, and so, I paid them a visit in person.

Sure enough, they stocked some automotive-grade vinyl fabric closely similar to the old vinyl in the car. I ended up with some from this product line They also supplied a sheet of headliner foam which, although not an identical match for the deck padding, serves the purpose very well (and it will be hidden from view anyways.) They even sold paperboard, which I can use to replace the original paperboard tray, which is already in pretty sorry state. Total cost for materials was about $40.

I highly recommend this place for any sort of fabric/upholstery need for your automotive project.


I had to glue two sheets of fiberboard together, as they were too thin by themselves. This took about half a bottle of wood glue, and a couple of days for the glue to dry. I then used the original tray as a template, drew an outline, and trimmed the board down to shape with a circular knife and lots of patience.

Next I cut the headliner foam to shape, and glued it to the fiberboard tray with spray-on glue.



I also drilled three holes for the fastening screws. I used 1/8" diameter aluminum spacers to line the holes and keep the screws from tearing into the cardboard.










Next, I stretched the vinyl sheet around the bard and fastened it using 1/4" tacks and a good-ol' hammer. Nothing better than pounding car parts into shape...





I had to figure out a replacement for the old paper trim piece at the rear of the tray. It looked old and ragged, and would detract from the look of the fresh vinyl.



I fashioned a replacement trim piece out of a long 6" wide strip of vinyl wrapped around a 2" strip of headliner foam, and held together with spray-on glue.





I then tacked the trim piece onto the rear of the tray. I used longer thumb tacks for this.







The end product looked very nice. The vinyl trim piece looked better than the original cardboard trim piece (in my opinion.)







Here is a look at the tray installed (with the brake light - more on that next time.)







Next up - third brake light gets installed.

Sunday, June 7, 2009

Long time, no driving...

It's been almost 6 months since my last post - time flies, doesn't it - and admittedly, I have not made as much progress since then. Yes, the car still is not running, the interior is not done, and there is no sign of having the car running any time soon - just like last time.

But I figured I'd update the blog and show where I'm going.

As you might recall, I needed to repair the heater core, as it was leaking coolant onto the pedal box. To do all this, I gutted out the interior carpetting, center console, and all the insulation associated with it. The plan was as follows:

- replace old/grimy insulation with something newer
- clean carpet and reinstall
- repair heater core and reinstall
- refurbish center console, and reinstall.

Well, I am still stuck in step one - replace insulation.

But before reinstalling the insulation, I had to deal with the bent jacking support, which had bent into the driver side floor pan. I took the car to Group 2, and they basically hammered the floor pan back into shape for me. It is not super strong, but for now, the repair is sufficient. The good news: the rocker/sill is perfectly good and strong, so structurally, the car is in good shape.

So, on to the insulation:

First, I cleaned up all the interior, basically lots of vacuum cleaning and good-ol' water and rags. The hammering of the driver side floor pan left a few spots with no paint, so I covered that area with Wurth Undercoating paint. This helps keep rust at bay, and it even helps with noise deadening! (Not that the localized application helps with that at all.)

Next, I started installing rubberized asphalt + aluminum sheets from B-Quiet over in Canada. Their Extreme product is similar to Dynamat, but at about half the cost. Since I saved so much money (right...) I also purchased their V-Comp product. The asphalt layer helps dampen vibration, while the V-Comp absorbs noise.

Installing the rubberized asphalt sheets is painstaking - a real pain in the butt (and the neck, back, arms, stomach, and legs. Seriously.) It is important to minimize any air pockets left between the sheets and the car body. To accomplish this, I cut lots of smaller pieces (about 6" x 18" sections) and pasted them inside the car. I started around the edges, worked my way up to the firewall, and finished the floor sections last. Using a wooden roller (and its handle for detail work) helps tremendously, but it still takes lots of work. I estimate I spent about 24 labor hours working on this.

A single 50 sq. ft. roll was sufficient for the job. The results look nice (so far.)

And that's all I've done so far.

Next up, I need to install the V-comp product. I ended up buying two 13.5 sq. ft. sheets for this task. This will not provide enough material, but I'll make sure to paste it onto the firewall, and the driver and passenger side floor sections. Any leftover material will be used around the transmission tunnel section, and then on the driveshaft tunnel section. I've already cut the pieces - I made templates out of newspaper, and cut to match - but I have not test-fitted them. I am very curious to see how it all comes out.

A few notes on this whole noise insulation thing:
- Again, this is very tedious work - especially in the cramped confines of my one-car garage. I see these kinds of material installed onto cars on TV shows all the time. They never say how long this takes - now I know why.
- The material is a bit messy - the rubberized asphalt leaves marks all over your clothes, hands, and skin. It's not too bad, but one has to be careful not to stain any parts of the house (e.g. the shower floor) when you are done working. (Don't ask me how I know...)
- The stuff is heavy. I estimate I'll be adding about 60lbs to the total weight of the car. On the plus side, it's fairly low in the car, but still, 60lbs cannot be a good thing.
- And I still don't know how well this stuff works. The GTV is a noisy car by nature, so I might be completely wasting my time with this. We'll find out soon enough.

Next up: A light detour...

Saturday, December 27, 2008

Carpet comes out.

With the heater core and center console removed from the car, I started thinking that removing the carpet would be faily straightforward. This runs counter to the "do only one project at a time" rule, but a few things became clear while working under the dashboard:

1) The interior carpet is pretty dirty
2) The insulation under the carpet looks old and ratty (at least, near the edges)
3) The carpet smells pretty bad. Actually, very bad...


Removing the driver and passenger seats involves removing four fasteners per seat. These fasteners are round-headed allen wrench types, and require a 7mm (?) allen wrench to remove. Once all four fasteners are removed, fold the seat and remove from the car. My seats were spaced with four 15mm or so plastic spacers. Make sure not to lose those.




The passenger seat worked the same way. However, due to space constraints, I had to remove it through the driver side. Although nothing bad happened, I would recommend not doing this if possible - it is annoying and difficult to get a good handle on things.



Removing the seatbelts was also very straightforward. I only removed the bottom anchors andleft the top anchor fastened to the side rear wall. My belts are old and somewhat frayed, so I think I'll replace those also.


The door sill trim plates do not need to be removed completely, but they need to be loosened up so that one can pull out the carpet from under them. They are held in place by four metal sheet screws. On my car, the screws use a square thread on the head, which required a few trips to the hardware store to get the proper-sized square key.

The E-brake boot comes out by pulling it. In the process, the boot itself fell apart. Again, another thing to replace. I may also pull out the e-brake assembly, just to clean it and refurbish it. Again, scope creep makes an appearance.

The rear seat plates are these L-strips of chromed metal which are screwed in place in the rear. Removing them is straightforward, but the strips' edges are sharp, and I ended up cutting myself ("it's just a flesh wound!") Very annoying!


Once all this is done, one just pulls out the carpet. The carpet is a single shaped piece, so pulling it requires a bit of finesse. Start from the farthest edge, pull back and fold towards yourself, then pull the near edges, fold away towards the rest of the carpet, and pull the whole "roll" out of the car.

Removing the carpet uncovered the insulation batting underneath. In my car, this looked very nasty - dirty, rusty, dusty, and just plain old. The batting seems to be made of cloth fabric, with a layer of bitumen/tar on top. My impression was that it was a pretty good quality piece, kinda like 40 year-old dynamat, with a 3/4 inch layer of fabric attached to it.
However, pulling the insulation batting would cause the top bitumen layer to crack. It also unleashed a dust storm inside the car. (Take the proper precautions if you ever do this.)

After trying to remove the insulation carefully, I realized I'd be throwing the old thing away anyways, as it was way too dirty and smelly, and the cracking of the bitumen was pretty much widespread. So I just started pulling the stuff without much regard for reusing it. It all folded compactly, and ended up going straight to the trash bag.

Underneath, I found a few things:
1) Lots of dirt - mostly dust from the insulation batting. I had to vaccum-clean and use wet rags to clean up the interior, and it came out OK.
2) No rust, just fresh red paint. This is good news, as any major rust under the carpeting would require major rebuilding measures
3) A bent floor pan area at the driver side foot well. This occured a few months back, when the driver side jacking point bent inwards. This will require a few strong sledge whacks, some welding, and a bit of paint. Fortunately, this all happens under the car, so the visible finish will not be affected.


After all this was done, I re-installed the driver seat. This allows me to drive the car in its current half-baked state. The interior looks a bit like a race car's, and driving it is even noisier. But this will allow me to drive the car to the shop to repair the jacking point/bent floorpan, and in case I need their help with anything else.

Tuesday, December 2, 2008

Heating and Cooling - Things to buy, things to repair.

So, in the process of removing the heater box, I ended up removing the center console and shift boots. In this entry, I'll focus on these two things.

The shifter has three boots:

1. An "outer" rubber boot (right in the picture below), which attaches to the shifter tunnel and the actual transmission case, where the shift lever sticks out. It seals the insde of the car from the outside (lower) part of the car.

2. A "middle" rubber boot (left in the picture below), which mounts on top of the outer boot, providing further noise insulation.

3. The upper vinyl boot, which is the one mounted on the console and is visible to the inside of the car.

The outer and middle boot were mounted incorrectly. Not that it matters, since both rubber boots were torn and pretty badly degraded. Furthermore, the plastic attachment used to mount the middle boot in place is a bit torn up, and needs some repair.

The vinyl boot is also torn up somewhat. I will have to purchase a new one (or maybe upgrade to leather.) These are easily sourced, as well as the rubber boots themselves.

The plastic attachement, well, they are not so easily sourced. I'll probably have to hack something to make it useable again. If I knew how to make fiberglass, or even carbon-fiber parts (gasp!), I would be considering doing something crazy right about now.


The console itself is also in so-so shape. It is made of a plastic shell, covered with thin vinyl, and accented with wood and crome trim. The plastic shell is in usable shape, but the various attachment points are torn up. I will have to hack some attachments in order to bolt it onto the car firmly.

The vinyl cloth is OK, but I suspect I want to actually remove and replace it. This would entail sourcing similar vinyl (not sure where, yet) and gluing it in place. Not sure how to best proceed, yet.

The wood trim looks very sun-faded. Although it still looks OK, I suspect I will want to replace it. Replacing it will involve sourcing some wood veneer (not sure which kind yet,) sanding and varnishing it, and installing the new pieces in place. As far as the chrome trim, I'll probably polish the heck out of it, and call it done.

Again, one can only wonder at how a carbon-fiber replacement (with brushed aluminum trim) would look. I think it would look phenomenal. I really should learn how to make CF parts...

Next up: The heater box comes apart.

Sunday, November 30, 2008

Heating and Cooling - Heater Box Removal

The next thing to do is to remove the heater core. Generally, this tends to be a big pain. You see, removing the heater core involves crawling under the dashboard, usually half upside-down, with very littler room to maneuver, while unfastening nuts and bolts in very tight and hard to reach places. Being a contortionist is not a requirement, but it is very helpful.

On the GTV, the center console must be removed before reaching the heater core. Although this is not difficult, it adds to the amount of work needed to be done. The console contains switches for actuating the wipers, heater fan, and fog lights, as well as a cigarrette lighter. These have wiring that must be disconnected and labeled, making things a bit slower.

Plus, the shift lever sticks right through the middle of the console. Again, adding to the amount of work required.

So, to start, one removes the shifter knob. On this car, the knob is a simple slip-on knob. One then removes a few screws holding the center console in place. This allows the console to be moved around, providing access to the wiring underneath the console itself.

During this whole process, I jiggled the cigarrette lighter and the various switches, just to figure out how to proceed. To my surprise, smoke starting coming out from around the lighter wiring. Holy cow! I pretty much panicked - images of the car burning down my house flashed through my mind. After fumbling for the hood lever, finally finding it and popping the hood, then looking for an unfindable 10mm wrench (is that the right size for the battery terminals?), and realizing this was taking way too much time, I figured I'd try to disconnect the wiring from the lighter itself. With the heating element glowing red, I reached in (half expecting to burn my fingers,) found the wires, and disconnected the lighter plug. Smoke streamed for a few more seconds ("what else is burning?") but then it faded and stopped altogether.

Moral of the story: always disconnect the battery when working with the car!

So, I proceeded to disconnect the battery terminal, and caught my breath. Talk about dodging a potential bullet. This is a lesson that I keep forgetting, and keeps biting me in the butt!

I then detached the wiper, heater, and fog lamp switches from the console. This allowed me to keep everything connected (and functional) while freeing up the center console itself. I also removed the heater temperature control levers and cover plates, and pulled the console out of the way.

At this point, the shift lever sits by itself, covered by two rubber boot. One of the rubber boots is supposed to cover the transmission tunnel, while the other one rests above it. In my car, they were flipped - the lower boot sat on top of the top boot! Removing the boots just involves pulling them out of the shift lever.

On closer inspection, both boots were torn. The bottom one (which should have been on top) was covered in tranny fluid (which explains some of the odors inside the car.) These things will need to be thrown out and replaced.

Once all this is removed, one can tackle the heater box itself.

One starts by removing the two air ducts connecting the heater box to the defrost vents. Each air duct is attached to the heater box by two nuts. Removing them was trivial. So far, so good.














The next thing is to disconnect the heater box from the electrical wiring. Not a big deal, but it requires labeling the wires to make sure we can connect them correctly again.

Next, one disconnects the coolant hoses from the heater box itself. I had already bypassed them, so they were mostly empty, but a bit of coolant dripped from them, nonetheless. These will be replaced with fresh hoses when putting everything back together again.



Next, one needs to unfasten the four nuts that hold the heater box in place. These nuts fasten around four studs connected to the top inside of the dashboard. Needless to say, these things are buried deep within wiring, ducts, and other parts under the dash.

To gain better access, I found it useful to remove the heater valve. After removing the heater valve, access to the two studs on the driver side was tricky, but with some patience, the nuts came out OK.

The two studs on the passenger side were a bit more accessible, but still, unfastening them was slow, patient work.


Once the mounting nuts are removed, the box can be jiggled out of place. However, there is barely enough clearance to pull the box out from under the dashboard. I eventually removed the bottom part of the heater box (the actual heater fan, as it turned out.) This allowed me to remove the box in pieces. This worked OK for now, but in all honesty, I am not sure how I'll put this all together back in place.

Overall, the box looks old and a bit rusty, but very rebuildable. The plastic parts need a good cleaning, but there is no apparent damage to it. The flapper doors (which route air to the floor, or up to the defroster vents) are rusty, but the rubber edge trim on them feels flexible and without any cracks or damage. The box needs cleanup and maybe some paint, but overall, it looks in very good shape.

Another surprise, however: the fan is actually a six-bladed fan. For my model year, the fan should have been a cylindrical "squirrel box" fan. I am not sure how the wrong fan type got in there, or to which car it belongs. It looks like a fan from an older vintage GTV, but I do not know for sure.

After all this, I bagged and labeled all the parts, and put everything away. The car is still driveable, although the transmission boots are missing, allowing noise and air to come through the transmission tunnel.

Next up: Things to buy, parts to repair.