Showing posts with label Paint. Show all posts
Showing posts with label Paint. Show all posts

Sunday, June 7, 2009

Long time, no driving...

It's been almost 6 months since my last post - time flies, doesn't it - and admittedly, I have not made as much progress since then. Yes, the car still is not running, the interior is not done, and there is no sign of having the car running any time soon - just like last time.

But I figured I'd update the blog and show where I'm going.

As you might recall, I needed to repair the heater core, as it was leaking coolant onto the pedal box. To do all this, I gutted out the interior carpetting, center console, and all the insulation associated with it. The plan was as follows:

- replace old/grimy insulation with something newer
- clean carpet and reinstall
- repair heater core and reinstall
- refurbish center console, and reinstall.

Well, I am still stuck in step one - replace insulation.

But before reinstalling the insulation, I had to deal with the bent jacking support, which had bent into the driver side floor pan. I took the car to Group 2, and they basically hammered the floor pan back into shape for me. It is not super strong, but for now, the repair is sufficient. The good news: the rocker/sill is perfectly good and strong, so structurally, the car is in good shape.

So, on to the insulation:

First, I cleaned up all the interior, basically lots of vacuum cleaning and good-ol' water and rags. The hammering of the driver side floor pan left a few spots with no paint, so I covered that area with Wurth Undercoating paint. This helps keep rust at bay, and it even helps with noise deadening! (Not that the localized application helps with that at all.)

Next, I started installing rubberized asphalt + aluminum sheets from B-Quiet over in Canada. Their Extreme product is similar to Dynamat, but at about half the cost. Since I saved so much money (right...) I also purchased their V-Comp product. The asphalt layer helps dampen vibration, while the V-Comp absorbs noise.

Installing the rubberized asphalt sheets is painstaking - a real pain in the butt (and the neck, back, arms, stomach, and legs. Seriously.) It is important to minimize any air pockets left between the sheets and the car body. To accomplish this, I cut lots of smaller pieces (about 6" x 18" sections) and pasted them inside the car. I started around the edges, worked my way up to the firewall, and finished the floor sections last. Using a wooden roller (and its handle for detail work) helps tremendously, but it still takes lots of work. I estimate I spent about 24 labor hours working on this.

A single 50 sq. ft. roll was sufficient for the job. The results look nice (so far.)

And that's all I've done so far.

Next up, I need to install the V-comp product. I ended up buying two 13.5 sq. ft. sheets for this task. This will not provide enough material, but I'll make sure to paste it onto the firewall, and the driver and passenger side floor sections. Any leftover material will be used around the transmission tunnel section, and then on the driveshaft tunnel section. I've already cut the pieces - I made templates out of newspaper, and cut to match - but I have not test-fitted them. I am very curious to see how it all comes out.

A few notes on this whole noise insulation thing:
- Again, this is very tedious work - especially in the cramped confines of my one-car garage. I see these kinds of material installed onto cars on TV shows all the time. They never say how long this takes - now I know why.
- The material is a bit messy - the rubberized asphalt leaves marks all over your clothes, hands, and skin. It's not too bad, but one has to be careful not to stain any parts of the house (e.g. the shower floor) when you are done working. (Don't ask me how I know...)
- The stuff is heavy. I estimate I'll be adding about 60lbs to the total weight of the car. On the plus side, it's fairly low in the car, but still, 60lbs cannot be a good thing.
- And I still don't know how well this stuff works. The GTV is a noisy car by nature, so I might be completely wasting my time with this. We'll find out soon enough.

Next up: A light detour...

Sunday, November 11, 2007

Work continues: steering linkage, part 1

I finally started working on the steering linkage of the Alfa. The idea was to replace just a few things in the front end, and then decide whether I want to tackle the whole job or not. One side of me wants to do all the work, since I find working on cars to be fun - I like the challenge (both mental and physical,) trying to figure things out, and engrossing myself in a task so much that I end up losing track of time (or the real world, for that matter.) And with a bit of luck, you end up with a better working vehicle.

On the other hand, this is the front suspension of the car, which can be pretty complicated stuff. Taking it to a shop will ensure that the work will be done right, and fairly quickly (1-2 days max.) Just drop off the car, come back the next day, and everything is A-OK. There is a lot of benefit in this - just drive the car and have fun.

I am still undecided as to what I will do. But in the meanwhile, I figured replacing all the steering ball joints should be straightforward enough.

So, last Wednesday night I jacked up the front end of the car, placed it on stands (ratchet-type jack stands), and went to work. I had borrowed a gear puller from my friend TJ (the puller on the left,) and was able to pull three of the six ball joints required. This puller worked well, but it was a very tight fit for the inner tie rods (four of them). I spent two and a half hours trying to figure things out! At this pace, I would be done sometime around Xmas.

So, I stopped for the night (11:30pm) and decided to look for the puller on the right (called a "ball joint lifter" - not a puller.) A few folks in the Alfa Bulletin Boards (www.alfabb.com) have recommended this type, and a few stores had them online. But I wanted it now, so I ended up going to Napa Auto Parts, and wouldn't you know it, they had it in stock. It only cost $12 with tax, so I figured I'd give it a shot.

So, Saturday morning, I got under the car at about 9am or so. Within 30 minutes all three remaining ball joints had been pulled off. Wee! I must say, having the right tool for a job saves a lot of time and effort. I highly recommend obtaining this kind of lifter for this kind of job, as it made the whole ball joint pulling (lifting?) experience a very simple one.

So, finally, the steering linkage was all out. I left the steering box and idler box in place, as I think servicing these are a bit beyond the immediate scope of things. I suspect the steering box could use a bit of maintenance, but for now, I'll just play with one thing at a time.

Before disassembling anything else, I measured the distance between ball joints, so that I can reset the length when I reassemble the whole thing. I'll have to align the car regardless, but hopefully the front alignment will be within a reasonable ballpark in the interim (what's a bit extra tire wear?)

The next problem was disconnecting the tie rods from the main rods themselves. At first I thought the locking nuts where part of the middle rods themselves. After much pounding at wrenches and the such, I realized the nuts and the rods were separate parts. Duh! They are locking nuts, after all. So I started pounding in different directions, and within 10 minutes, everything was disconnected.

The joints themselves were to be thrown out, but the middle rods themselves will be reused. They were all grimy with grease, undercoating, paint, and rust. So I figured I'd clean them up and paint them.

I started by cleaning the rods with brake cleaner and a stiff wire brush. After about 1o minutes of scraping away, the things were fairly clean. Brake cleaner is nasty stuff, but it does clean everything in sight. I then sanded the rods with medium grit sandpaper, and re-sprayed with even more brake cleaner.

Afterwards, I rinsed everything with hand clener (Fast Orange) and plenty of water.

The results are shown on this picture. One of the rods was pretty much striped down to bare metal. The other two were down to the original paint (?) with some spots of bare metal. All signs of grease and undercoating was gone, as well as most of the rust.



I then painted the rods with a few light coats of Rust-Oleum Semi Gloss paint. The things look pretty nice now - not bad for the first time I've ever spray painted anything in my life. The whole paint work (prep, and painting itself) took about 45 minutes.

I would have done a few things differently:
a) I would have used a finer grit sandpaper, as the finished surface looks a bit rough, and not shiny smooth.
b) I would have used a full-gloss paint. I am realizing I want the suspension to be glossy and shiny.

Before re-installing all this back onto the car, I want to replace the lock nuts used to lock the rods and the ball joint links together. I abused the crap out of them when I was removing them earlier, so I figured it would be better to replace them. The lock nuts are sized 14mm x 1.50 thread pitch (for those keeping score at home,) but I need both right-handed and left-handed thread nuts. I did find the RH type at the hardware store down the street, but they did not stock the LH kind. I will be looking for the LH nuts during the week.

Once I find them, then I can re-install the tie rods to the main rods, then install stuff back onto the car. Hopefully the car will be back on its feet next weekend. We'll see how that goes.